Seneca ZC-16DI-8DO, 24-Channel, 16 Digital Input/8 Digital Output CANopen/ModBUS Module

Seneca ZC-16DI-8DO, 24-CH, 16 Digital Input/8 Digital Output CANopen/ModBUS Module

Price: (4 or fewer items) £200.00 (Excluding VAT at 20%)
Price: (5 to 9 items) £194.00 (Excluding VAT at 20%)
Price: (10 to 24 items) £188.00 (Excluding VAT at 20%)
Price: (25 or more items) £182.50 (Excluding VAT at 20%)

Quantity:

Description:

The module ZC-16DI-8DO acquires 16 single-ended digital signals, it converts them to a digital format (IN 1-16 state) and it counts the input-pulse number (pulse counter for IN 1-8). It also controls 8 digital outputs (OUT1-OUT8), each of them (by MOSFET) actives/deactivates a output load.

General Characteristics :

Acquisition of digital signals from sensor: reed, NPN, PNP, proximity, contact, etc...

Configuration of a filter applied to input signals IN1-IN8 (noise filter) to attenuate the noise overlapped to the digital signals

Pulse counters for digital signals IN1-IN8, with max frequency equal to 10kHz, 32bit-registers

Advanced management of the pulse counters for digital signals IN1-IN8 (for each pulse counter: overflow, preset value and reset/preset command are available)

Power of 16 sensors using internal supply voltage (Vaux=16V)

Outputs are available on 8 screw terminals or IDC 10 connectors, to facilitate the connection of 24V-relays

It is possible to manage the output state if the interval time of RS485-bus communication failure is greater than a configurable time (up to 25.5sec): output is kept at the previous value or output is overwritten on register

It is possible to manage the output state if there is a over-temperature or short-circuited (towards ground)

Configuration of the module (node) address and baud-rate by Dip-Switches<.li>

It is possible to add/remove the module to/from RS485-bus without disconnecting the communication or power supply

It is possible to switch automatically RS485 to RS232 or vice versa

CAN interface with CANOpen protocol: max 1Mbps

Specification:

Order code :		ZC-16DI-8DO
Description:		16 CH digital input - 8 CH digital output CANopen / ModBUS
Power Supply:		10..40 Vdc, 19..28 Vac
Max power consumption:		2,5 W
Isolation:		1,5 kVac (3 way)
Response time:		1,2..2,5 ms
Operating temperature:		-10..+65°C
Dimension:		35 x 100 x 112 mm
Digital input:		16 channels; IEC EN 61131-2; Nr 8 counters @32 bit (max 10 kHz); TPDO < 1 ms
Digital output:		8 channels, 32 bit (max 10 kHz); mosfet, max 500 mA per channel, Vext 5..30 Vdc; RPDO < 1,25 ms

User configuration will require the S117P1 device (which can be purchased here) and the free EASY-SETUP software (which can be downloaded below).

Please refer to the following documentation for additional information:

Items:
Value:

Find us on the following social networks:

FREE CONFIGURATION & TECHNICAL SUPPORT INCLUDED WITH MOST ORDERS
Click here for more details

FREE ISS Ltd. Mug With All Orders Over £100.00 GBP

Seneca ZC-16DI-8DO, 24-Channel, 16 Digital Input/8 Digital Output CANopen/ModBUS Module

Seneca ZC-16DI-8DO, 24-CH, 16 Digital Input/8 Digital Output CANopen/ModBUS Module

Price: (4 or fewer items) £200.00 (Excluding VAT at 20%) Price: (5 to 9 items) £194.00 (Excluding VAT at 20%) Price: (10 to 24 items) £188.00 (Excluding VAT at 20%) Price: (25 or more items) £182.50 (Excluding VAT at 20%)

Price: (4 or fewer items) £200.00 (Excluding VAT at 20%)
Price: (5 to 9 items) £194.00 (Excluding VAT at 20%)
Price: (10 to 24 items) £188.00 (Excluding VAT at 20%)
Price: (25 or more items) £182.50 (Excluding VAT at 20%)